Yazar "Yüksel, Behiye" seçeneğine göre listele
Listeleniyor 1 - 3 / 3
Sayfa Başına Sonuç
Sıralama seçenekleri
Öğe Evaluation of the electrochemical corrosion behavior of anodic aluminum oxide produced by the two-step anodization process(Emerald Group Publishing Ltd, 2020) Yılmaz, Bengisu; Hapçı Ağaoğlu, Gökçe; Yüksel, Behiye; Orhan, GökhanPurpose This study aims to investigate the effect of different pore diameter and pore length on corrosion properties of anodic aluminum oxide (AAO) film. Design/methodology/approach AAO layer was produced by two-step anodization aluminum in oxalic acid. The surface morphology was investigated using field emission scanning electron microscopy. The pore diameters were ranging from 25 +/- 5 to 65 +/- 5 nm and the pore length ranging from 5 to 17 mu m. The corrosion properties of the AAO films was analyzed by potentiodynamic polarization and electrochemical impedance spectroscopy tests. Corrosion properties and morphology of the anodic films depending on anodization times and pore expansion times were evaluated. Findings All highlights of this work can be summarized with the following specified below: more treatment with the protective barrier layer of the solution as the pore diameter increases depends on the morphology of the nanotube structured AAO layer. The excellent corrosion resistance renders AAO films without pore expansion very promising. The oxide layer thickness does not affect the corrosion resistance. The better corrosion resistance of AAO films at low pore length can be ascribed to the barrier layer thickness and the more homogeneous structure. The presence of defects for the higher pore length decreases its corrosion resistance. Originality/value The AAO films were fabricated by a two-step anodization method in oxalic acid. The anodization times and pore expansion times affect the corrosion performance. The AAO film without pore expansion has good corrosion resistance. The corrosion resistance decreases as the pore length increases.Öğe Isıl İşlemin Akımsız Ni-B/Ni-B-W Dubleks Kaplamanın Korozyon Direncine Etkisinin Analiz Edilmesi(2020) Dil, Gökçe; Gökşenli, Ali; Yüksel, Behiye; Muhaffel, FaizBu çalışmada çelik malzemenin yüzeyi, akımsız kaplama yöntemi ile Ni-B/Ni-B-W ile kaplanmış, kaplamaların içyapı ve korozyon direnci incelenmiştir. Ni-B/Ni-B-W kaplaması asidik hipofosfit ve alkalin borohidrid indirgeyici banyolarla akımsız olarak kaplanmıştır. Kimyasal bileşim analizi için EDS yöntemi kullanılmıştır. Tarayıcı Elektron Mikroskobu (SEM) ile kaplamanın kesit ve yüzey morfolojisi incelenmiştir. SEM analizi sonucu kaplamaların üniform olduğu, yüzeye çok iyi bir adezif bağ ile gözeneksiz bir şekilde bağlandığı ve kaplamaların birbirleriyle uyumlu olduğu gözlemlenmiştir. XRD analizleri sonucu her iki kaplamanın da amorf yapıda olduğu,450 ºC’de bir saat uygulanan ısıl işlem ile kaplamanın kristalleştiği ve nikel borit (Ni2B ve Ni3B) çökeltilerinin oluştuğu tespit edilmiştir. Çelik, ısıl işlem görmemiş ve görmüş Ni-B ve Ni-B/Ni-B-W kaplamaların korozif karakterini incelemek için 5% H2SO4 çözeltide daldırma ve Potansiyometrik Polarizasyon deneyleri (%3,5 NaClsulu çözeltide) gerçekleştirilmiştir. Deneyler sonucu her iki tür kaplamanın korozyon direncinin kaplanan malzeme olan çelikten daha yüksek olduğu görülmüştür. Isıl işlem görmemiş Ni-B/Ni-B-W kaplamasının korozyon direncinin Ni-B kaplamaya göre daha iyi olduğu gözlemlenmiştir. Isıl işlemin uygulanması sonucu her ikikaplamanın da korozyon direnci artmıştır. Ancak Ni-B/Ni-B-W dubleks kaplamasında artış Ni-B kaplamaya göre daha fazladır. Kaplamaya tungstenin eklenmesi ile ısıl işlem sonrası yüzeyde oluşan koruyucu tungsten oksit tabakasından dolayı, kaplamanın korozyon direnci artırmıştır.Öğe Synthesis and characterization of salt-impregnated anodic aluminum oxide composites for low-grade heat storage(Springer, 2020) Yılmaz, Bengisu; Yüksel, Behiye; Orhan, Gökhan; Aydın, Devrim; Utlu, ZaferThermochemical heat storage (THS) systems have recently attracted a lot of attention in research and development. In this study, an anodic aluminum oxide (AAO) template, fabricated by a two-step anodization method, was used for the first time as the matrix material for a THS system. Different salts were studied as thermochemical materials for their suitability in low-grade heat storage application driven by solar energy for an open system. Compositions were prepared by absorbing CaCl2, MgCl2, LiCl, LiNO3 and mixtures of these salts under a vacuum in an AAO matrix. Field Emission Scanning Electron Microscopy was used to examine the morphology of the produced AAO composites. Thermal energy storage capacities of the composites were characterized using a differential scanning calorimeter. Characterization analysis showed that anodized Al plates were suitable matrix materials for THS systems, and composite sorbent prepared with a 1:1 ratio LiCl/LiNO3 salt mixture had the highest energy value among all composites, with an energy density of 468.1 kJ center dot kg(-1).